Like every other website on the planet, SmallNetBuilder uses cookies. Our cookies track login status, but we only allow admins to log in anyway, so those don't apply to you. Any other cookies you pick up during your visit come from advertisers, which we don't control.
If you continue to use the site, you agree to tolerate our use of cookies. Thank you!

Router Charts

Click for Router Charts

Router Ranker

Click for Router Ranker

NAS Charts

Click for NAS Charts

NAS Ranker

Click for NAS Ranker

More Tools

Click for More Tools

LAN & WAN Basics


After our tours through port management and security, it's time to wrap up this series with a review of what a smart switch can do for bandwidth management. In the GS108T, these functions fall under the QoS tab.

Rate Control

I'll come back to the Global Configuration screen and instead skip right to where you can start ratcheting down bandwidth with minimal muss or fuss. Figure 1 shows the port-based Rate Control settings.

QoS Rate Control

Figure 1: QoS Rate Control

All you need to do is decide whether you want to control the rate of traffic coming into (Ingress Rate) or out of (Egress Rate) a port, select the desired rate from the dropdown and save the settings. The main limitation of the GS108T's rate control is that it may not be much help for limiting Internet traffic because there aren't a lot of "clicks" below 10 Mbps and only one below 1 Mbps. But if you need to limit traffic on your LAN, the settings are probably fine.

I ran a quick IxChariot test to see how smooth rate limiting was. Figure 2 starts with no limiting and then applied limits of 60, 200 and 400 Mbps. Implementations of bandwidth limiting that I have seen on previous generation smart switches and more notably in consumer routers, appeared to control bandwidth by completely turning traffic on and off and varying the ratio of "on" and "off" time. In contrast, the GS108T's rate limiting looks very smooth.

Rate limiting in action
Click to enlarge image

Figure 2: Rate limiting in action

Note that because a smart switch is a Layer 2 device, it can't rate limit specific services such as BitTorrent, FTP, etc. and it also can't rate limit by IP address. Rate limiting works only by physical port and all traffic through that port.

Priority Based QoS

With the simple stuff out of the way, let's move on to packet priority QoS features. Figure 3 shows the Global Configuration screen where you set the switch to handle packet priority via DSCP (Diffserv) or 802.1p. Both are protocols for communicating the priority of network packets, with the difference being that 802.1p is a Layer 2 protocol and DSCP is Layer 3.

QoS Global Configuration

Figure 3: QoS Global Configuration

The significance of the difference is that choosing 802.1p means that traffic will be prioritized on your LAN only. Once 802.1p packets hit a router, the 802.1p header will probably be dropped. This post, by a Microsoft QoS expert also mentions other reasons why 802.1p headers get lost. So, to me, 802.1p sounds like a not-so-good choice.

As a Layer 3 protocol, DSCP will survive going through routers (assuming they are DSCP-capable) and generally is considered more robust. DSCP also has the advantage of being visible to network sniffers like Wireshark, where 802.1p tags generally aren't. The reason why is mentioned in the Microsoft link above and in more detail here.

Actually, you probably won't be using either 802.1p or DSCP in a small LAN, since the sending and receiving devices actually have to set and act on the priorities communicated in the data. But if you do, the GS108T lets you map the eight 802.1p priorities (numbered 0 to 7) to four switch priority queues (Lowest, Low, Normal, Highest) if you select 802.1p based QoS.

If you select DSCP Based QoS, the DSCP Priority Mappings would be in effect. Figure 4 shows what those mapping look like. Aren't you glad that you have the simple Rate Limiting controls?

QoS Global Configuration

Figure 4: DSCP to Priority Mapping

More Basics

Wi-Fi System Tools
Check out our Wi-Fi System Charts, Ranker and Finder!

Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!

Over In The Forums

Hi all. I see alot of posts about backhaul here and could use some clarity. As I understand it, I can go with Wired ethernet backhaul, or Wifi backhau...
Hi. My router after reboot changes disk names from sda to sdb & back, if I reboot another time. I give labels to both disks - NET & NET2 ,but it happe...
Hi everyone, this is my first post ever here. Hope the answers will be helpful to other users, too …I'm trying to connect two RT-N14UHP routers with t...
HiRT-AC87U, Firmware Version 384.9Router 1, VPNRouter 2, Non VPNThe both routers do have VPN servers setup in them, but mostly Router 2 is used with p...
Hello all!I was planning to use my RT-AC56U as a serial debug bridge for an Odroid board which is close by. I hooked up a USB cp210x adapter into its ...

Don't Miss These

  • 1
  • 2
  • 3