Like every other website on the planet, SmallNetBuilder uses cookies. Our cookies track login status, but we only allow admins to log in anyway, so those don't apply to you. Any other cookies you pick up during your visit come from advertisers, which we don't control.
If you continue to use the site, you agree to tolerate our use of cookies. Thank you!

Router Charts

Click for Router Charts

Router Ranker

Click for Router Ranker

NAS Charts

Click for NAS Charts

NAS Ranker

Click for NAS Ranker

More Tools

Click for More Tools

LAN & WAN Features

Introduction

DD-WRT and Tomato Don't Fix Everything

Judging from some of the threads I see in networking discussion forums, alternative router firmware has its share of fanboys. You frequently see responses that boil down to "...the factory firmware is crap. Just load [insert favorite alternative firmware here] onto your router and everything will be fixed..."

Well, I finally got around to loading up a few of these magic beans and did some basic testing to see what effect they had on routing throughput, variation and session handling. I didn't really know what to expect, but what I found might give some potential firmware switchers pause before pulling the trigger.

The Firmware

To keep things simple, I chose two of the most popular alternative firmwares for consumer routers: DD-WRT and Tomato.

DD-WRT has a long history. To quote from the DD-WRT Wiki:

The first versions of DD-WRT were based on the Alchemy Firmware from Sveasoft Inc, which is in turn based on the original GPL'd Linksys firmware and a number of other open source projects. DD-WRT was created directly from Sveasoft's software decision to start charging for their firmware, closing the door to opensource.

DD-WRT comes in various flavors, including reduced-feature builds for newer routers with only 2 MB of flash and versions that add VoIP and VPN features to an impressively large base feature set. It supports routers based on Broadcom or Atheros processors.

Tomato is a relative newcomer, positioning itself as "a small, lean and simple replacement firmware". It supports only Broadcom-based routers, in particular, Linksys' WRT54G/GL/GS and Buffalo WHR-G54S/WHR-HP-G54.

The Router

I didn't want to spend time finding about all the things that can go wrong with uploading alternative firmware. So I chose the Linksys WRT54GL (v1.1) as my test platform. It has 16 MB of RAM and 4 MB of flash. It was created by Linksys in response to the outcry from the alternative firmware crowd when Linksys cut RAM and flash in half on the WRT54G starting with V5.0.

Linksys WRT54GL

Figure 1: Linksys WRT54GL

I looked at both the WRT54G V5.0 and WRT54GL about two years ago and found the WRT54G better than the WRT54GL in terms of throughput consistency, but the GL better for simultaneous session handling.

More LAN & WAN

Wi-Fi System Tools
Check out our Wi-Fi System Charts, Ranker and Finder!

Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!

Over In The Forums

Hello,I have an RT-AX88U connected wirelessly through aiMesh to two RT-AX92U access points. Strangely, one of these nodes often goes to sleep even whe...
Is there an NVRAM variable or some other trick to determine in a script if it is running on a node or on the main router? I tried searching the NVRAM...
So, i was fed up with my older router's poor range, so picked up an RT-AC86U from eBay - it is excellent, very pleased.However, I can't figure out to ...
I just purchased a rt-ax888u and im trying to get over 100mbit with the vpn...im using ipvanish...are there settings i need to use for the vpn to run ...
Wireless Router ModeFirmware 384.15Hello and thanks for allowing me to participate in SNB forums!I'm an IT admin with pretty good grasp of networking/...

Don't Miss These

  • 1
  • 2
  • 3