Like every other website on the planet, SmallNetBuilder uses cookies. Our cookies track login status, but we only allow admins to log in anyway, so those don't apply to you. Any other cookies you pick up during your visit come from advertisers, which we don't control.
If you continue to use the site, you agree to tolerate our use of cookies. Thank you!

Router Charts

Click for Router Charts

Router Ranker

Click for Router Ranker

NAS Charts

Click for NAS Charts

NAS Ranker

Click for NAS Ranker

More Tools

Click for More Tools

LAN & WAN Reviews


NETGEAR XAVB5001 Powerline AV 500 Adapter Kit
At a Glance
Product NETGEAR Powerline AV 500 Adapter Kit (XAVB5001)
Summary HomePlug AV compatible, IEEE 1901-compliant powerline adapter kit with Gigabit Ethernet LAN port and higher maximum throughput than HomePlug AV
Pros • Close to 100 Mbps of single-stream throughput
• HomePlug AV certified and interoperable
• Only about 20% throughput drop with distance
• Very low throughput variation in general
Cons • High throughput variation when adapters are close together (same room)

My review of TRENDnet's first-to-market TPL-401E2K 500 Mbps powerline adapter kit ended with a question (actually two). Did TRENDnet's product really have design issues that caused its less-than-impressive performance? Or was Atheros' AMP 500 "500 Mbps" HomePlug AV compatible technology still not fully baked?

NETGEAR was finally able to get me an XAVB5001 kit (direct from Taiwan, no less). And to kill the suspense, it performs better than TRENDnet's adapters. But it also seems that Atheros still has some tuning to do, to bring out the full potential of its "500 Mbps" powerline technology.

The TRENDnet article has all the background on how Atheros' AMP 500 works, so I won't repeat it here. The gist is that it uses almost twice the spectrum that 200 Mbps HomePlug AV uses. So it can achieve higher throughput, if those higher frequencies can make it through your home's AC wiring.

The inside photo in Figure 1 of one of the two XAV5001 adapters in the XAVB5001 kit, shows an impressively heavy heatsink that's coupled to the main devices via a thick thermal pad. The heatsink isn't tied down; it is held in place only by the top cover.

This heatsink, plus generous use of vent grilles on all sides of the adpater should help keep the devices inside within proper operating range, even if the front cover of the adapter gets a bit warm to the touch.

NETGEAR XAVB5001 inside

Figure 1: Inside the XAV5001

Removing the heatsink reveals a familiar chipset (Figure 2): a large Atheros AR7400 MAC / PHY, flanked by an AR1500 Analog Front End (AFE) to its upper right and an Atheros AR8021 Gigabit Ethernet PHY to the lower left. If the XAV5001 hews closely to Atheros' reference design, there will be 16 MB of RAM and some amount of flash sitting on the bottom of the board.

NETGEAR XAV5001 board detail

Figure 2: XAV5001 board detail

There is actually another board on the very bottom of the package, connected to this top board by a 10 pin connector. The bottom board is probably where a lot of the AC line coupling and power conversion circuitry sits.

Setup And Administration

HomePlug adapters are factory set to plug in and go, and the pair of XAV5001's did. I had no problem with the adapters auto-negotiating Gigabit links with my Acer Aspire 1810T test notebook with Atheros AR8131 PCI-E Gigabit Ethernet controller and NETGEAR GS108 Gigabit switch.

Figure 3 shows a summary of the adapter's lights. Note that the three color signal quality light seen on some HomePlug AV roundup adapters and the TRENDnet TPL-401E is also incorporated into this product. Looks like a standard feature of the Atheros chipset.

NETGEAR XAV5001 ports and indicators

Figure 3: XAV5001 ports and indicators

You also get a Security button that you can use to change the default "HomePlugAV" 128 bit AES encryption key. This is a good idea if you live in a dorm or apartment building where your powerline signal could stray beyond your home. The button doesn't change the security encryption strength, just the encryption key.

I didn't find a utility on the CD that came in the box. So I hit the XAVB5001 support page to download the utility. I also downloaded the XAV5001 Firmware Upgrade Utility v2.0.0.0 while I was at it.

The utility is much fancier than TRENDnet's, but does essentially the same thing. I didn't get prompted to install WinPCap as I did when installing TRENDnet's utility. But perhaps that could have been because it had been previously installed.

More LAN & WAN

Wi-Fi System Tools
Check out our Wi-Fi System Charts, Ranker and Finder!

Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!

Over In The Forums

v2.5.1 Updated 2020-05-10 Run an NTP server for your network. Graphs available for NTP accuracy on the Addons page of the WebUI.Inspired by kvic's p...
Hi there,This thread is about GNUton's Merlin builds for DSL devices.* A few words about how this project started:Some days back I bought a DSL-AC68U....
Hi all, I have been considering upgrading the home network primarily as it pertains to security. With the implementation of many IoT devices which wil...
I updated my ISP from 200 to 400 Mbps. So I tested the throughput, the ISP Modem is putting out 467 Mbps. I am testing using an ethernet cable directl...
Hello everyone, I recently bought an Asus RT-AX58U router for my mom's 2 story house. I'm very happy with the purchase but i'd like to extend the w...

Don't Miss These

  • 1
  • 2
  • 3