Like every other website on the planet, SmallNetBuilder uses cookies. Our cookies track login status, but we only allow admins to log in anyway, so those don't apply to you. Any other cookies you pick up during your visit come from advertisers, which we don't control.
If you continue to use the site, you agree to tolerate our use of cookies. Thank you!

Router Charts

Click for Router Charts

Router Ranker

Click for Router Ranker

NAS Charts

Click for NAS Charts

NAS Ranker

Click for NAS Ranker

More Tools

Click for More Tools

LAN & WAN Reviews


The TPL-421E uses Qualcomm's QCA7500 HomePlug AV2 MIMO IC. Check the PLA5405 review if you'd like to see the device block diagram, or just download the data sheet.

The 421E's inside photo shows the QCA7500 at lower left. That's an Atheros AR8035 Gigabit Ethernet PHY right above it. There is no separate analog front end (AFE) device; that function is built into the QCA7500. This board is plugged into another board below it that has the wall plug and mostly passive components.

TRENDnet TPL-421E inside

TRENDnet TPL-421E inside

The 421E didn't get very hot during testing, despite its lack of heatsinks. The large ventilation slots on both sides of the device appear to keep it cool enough. It also helps that components aren't jammed into a tiny box. Here's a fuzzy view of the unplugged board underside showing 128 MB of Samsung K4B1G1646G RAM and 4 MB of Macronix MX25L3206E flash.

TRENDnet TPL-421E board bottom

TRENDnet TPL-421E board bottom


TRENDnet includes a Power Packet Utility on the CD packed in the 421E2K's box. You can also download it from the product's support page. It requires WinPcap 4.1.3, which will also be installed if it isn't already. The screenshot below shows the Utility, which doesn't expose the incomprehensible QoS controls some other powerline utilities do.

The screenshot was taken with both adapters plugged into the same power strip, showing a 910 Mbps link rate. I was transferring a large sequential file when this screenshot was taken. Printing out the utility's report showed the identified the adapter firmware as MAC-QCA7500-

Power Packet Utility

Power Packet Utility

You can also use the utility to set the encryption key (aka password) if you don't want to use the pushbutton method.


I tested the TPL-421E using our standard powerline test procedure, with all results entered into the Powerline Performance Charts. I included two other top-ranked AV2-MIMO adapters, NETGEAR's PL1200 and TP-LINK's TL-PA8030P-KIT and the 421E's TPL-420E2K no-outlet sibling.

The Downlink Throughput plot below shows the TPL-421E having the highest throughput in the best-case same-outlet Location A, but in no other test location. Top throughput in Locations C and E was produced by TP-LINK's TL-PA8030P-KIT.

Downlink throughput comparison

Downlink throughput comparison

Uplink results show the same relative performance results as downlink.

Uplink throughput comparison

Uplink throughput comparison

The simultaneous up /downlink IxChariot plot for the TPL-421E at Location A shows higher average downlink throughput after an initial position swap. The 523 Mbps total throughput result was 17% higher than 446 Mbps Location A downlink result.

IxChariot simultaneous up / downlink

IxChariot simultaneous up / downlink

I'm showing the composite downlink IxChariot plot because the Location A trace was so flat and maximum throughput was an even 500 Mbps. I asked TRENDnet whether this was expected behavior and they said it was within the range of what they've seen.

IxChariot composite dowlink throughput tests

IxChariot composite dowlink throughput tests

More LAN & WAN

Wi-Fi System Tools
Check out our Wi-Fi System Charts, Ranker and Finder!

Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!

Over In The Forums

This thread is for the discussion topic : unbound_manager script. As per the GitHub Hints/Tips: Differences between the operational modes​ E...
Hi,I'm about to setup a Xioami button that upon click should enable disable a VPN Client on the router settings. I use an IPTV server that at times ge...
Continuation of. . .
Hi all, I'm hoping someone can help. My Google Wifi (GW) mesh performance has slowed ton a crawl lately. Even with all the pucks in the same room, I w...
I read in another thread that updating to a newer firmware fixed the issue, which seems to be that dnsomatic switched to https only updating. In the l...

Don't Miss These

  • 1
  • 2
  • 3