Like every other website on the planet, SmallNetBuilder uses cookies. Our cookies track login status, but we only allow admins to log in anyway, so those don't apply to you. Any other cookies you pick up during your visit come from advertisers, which we don't control.
If you continue to use the site, you agree to tolerate our use of cookies. Thank you!

Router Charts

Click for Router Charts

Router Ranker

Click for Router Ranker

NAS Charts

Click for NAS Charts

NAS Ranker

Click for NAS Ranker

More Tools

Click for More Tools

NAS How To

Disk Installation

I started by opening up the T5700 and removing the flash module. I then connected the 44-pin IDE cable to the motherboard (Figure 6).

Figure 6: HP T5700, cover open with 2.5" IDE drive installed

Be careful to note the location of pin 1 on the header and the red stripe on the ribbon cable (Figure 7). Unlike larger IDE connectors, the laptop-sized header is not keyed, so the cable can be connected in reverse, with possibly tragic consequences.

Closeup of the IDE cable connecting to the T5700 motherboard
Figure 7: Closeup of the IDE cable connecting to the T5700 motherboard

The hard drive is mounted by simply taking advantage of the holes in the metal portion of the expansion chassis. The mounting holes in the drive are not on the same spacing as the holes in the chassis. So just rotate the drive until two of it mounting holes line up with two holes in the sheet metal (Figure 8). Two screws are adequate to mount the drive. If you feel it needs to be more secure, you could always lash the drive into place with nylon cable ties.

T5700 expansion side showing HD mounted by 2 screws
Figure 8: T5700 expansion side showing HD mounted by 2 screws

If you're not using the T5700 expansion chassis, then the drive will still fit. But you'll need to be careful to locate it so that it doesn't interfere with any of the heat sinks or connectors on the T5700 motherboard when the case is closed.

New models in the HP thin client family have faster CPUs and larger internal heatsinks. This makes mounting the drive a little trickier, but it can still be made to fit nicely into the standard chassis. However, the normal chassis side is a solid sheet of metal, so you can simply drill four holes to mount the drive in the desired location.

Rear view of the T5700 with the expansion side added
Figure 9: Rear view of the T5700 with the expansion side added

When using the expansion chassis, you need to install a filler blank in the back where the PCI card would normally reside (Figure 9). This will keep the system from accumulating dust internally.

T5700 with and without the expansion chassis
Figure 10: T5700 with and without the expansion chassis

It's also worth mentioning that HP does not intend the T5700 to run while sitting horizontally. They provide the little stand for a reason—cooling. The basic chassis is designed to cool properly when oriented vertically. The extra perforations in the expansion chassis reduce cooling issues to a degree. But I still prefer to stand the unit vertically.

More NAS

Wi-Fi System Tools
Check out our Wi-Fi System Charts, Ranker and Finder!

Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!

Over In The Forums

Hi guys,So I own 2 pc of ASUS ax88u since August.I have issue with upload speed.It is that specfic , that I know only of 6 people who have this glitch...
aegis is the successor of firewall-blocklist: sta...
Hey there, long-time reader here, finally created an account for this issue. I just can't get this router to work.Story is: I bought a customer return...
Due to new forum rules on threads older than six months, here is a fresh new one, good until April 2021.Previous threadAegisA firewall blocklist scrip...
Hi Everyone,I recently switched from a setup of Asus AC3100 (primary) and a wired Tplink AC2600 (access point) to a setup of Asus AC2900 (primary) and...

Don't Miss These

  • 1
  • 2
  • 3