Like every other website on the planet, SmallNetBuilder uses cookies. Our cookies track login status, but we only allow admins to log in anyway, so those don't apply to you. Any other cookies you pick up during your visit come from advertisers, which we don't control.
If you continue to use the site, you agree to tolerate our use of cookies. Thank you!

Router Charts

Click for Router Charts

Router Ranker

Click for Router Ranker

NAS Charts

Click for NAS Charts

NAS Ranker

Click for NAS Ranker

More Tools

Click for More Tools

NAS How To

SAN Performance

We are looking for Old Shuck’s SAN node performance figures, that is the speed over our 4Gb fiber link to BlackDog, our DAS node. These numbers should be much better than those of a comparable native drive, let alone our initial NAS speeds. Figure 19 shows our test topology.

DAS to SAN Test Topology

Figure 19: DAS to SAN Test Topology

When initially started testing our SAN performance using Intel’s NASPT test suite, we got some outrageous numbers, like 2010 MB/s for the ‘File Copy from NAS’ test, and 1633 MB/s for ‘4x HD playback’. These indicated something was wrong or that we had inadvertently overclocked our PCIe x4 slot by a factor of two. Since there wasn’t any smoke pouring out of BlackDog, we guessed something was wrong.

After some brief research, we realized that we were boneheads, NASPT recommends a maximum of 2 GB of memory, being a Java application it uses the JVM for memory management. At 8 GB, caching was giving us speeds that were not in the realm of possibility (as much as we wanted to believe them…)

When we stripped back BlackDog down to 2 GB and retested, results emerged that made more sense (Figure 20).

Old Shuck SAN Performance

Figure 20: Old Shuck SAN Performance

Very sweet numbers, with two exceptions, the Content Creation figure of 13.7 MB/s, which was most likely due to our stripe size, and the File Copy to Old Shuck, at 65.4 MB/s, still mysteriously low. Hopefully our planned tuning of BlackDog/Old Shuck as a logical NAS, in the next part, would give us a clue why this number was so much lower than our commercial competitors. It has us scratching our heads…

In Figure 21, we can see how we measure up against the SNB top performers. In all but the anomalous File Copy to NAS category, we trounce ‘em. But that is not a surprise, we’ve unfettered the traffic from the constraints of our Gigabit network.

Performance Comparison

Figure 21: Performance Comparison

Interestingly, if we compare the test figures of our SAN against those of the same kind of hard disk (compressed) connected on BlackDog’s SATA bus, Old Shuck still shines – putting CPU and fiber muscle behind the same model of disk makes a big difference (figure 22).

Hard Drive plus Standings

Figure 22: Hard Drive plus Standings

Wrap Up

Though the conversion / configuration process is a bit complex, it is straightforward and took about 30 minutes, the most difficult part is making sure the scst configuration file is correct.

And as you can see by the benchmarks, the performance is outstanding.

Let’s say you make your HTPC the DAS server, running a long fiber cable from your living room (the WAF factor for the Norco case is right up there with the dogs playing poker painting), converting the NAS you built to a SAN for less than $300. Now you are able to stream the densest Blu-Ray resolution known to man directly to your TV without a hitch, dramatically reduce the time it takes to rip that same Blu-Ray disk - and store, if fully loaded, about fifty more terabytes beyond that.  Do backups and update music and pictures from any machine in the house via that shared drive.

You won’t have to worry about performance or storage for quite some time (or until 2015, when storage guru Tom Coughlin comes knocking at your door with his Petabyte.)


In figuring out how to convert our NAS to a SAN, I’d be remiss in not thanking the sources used in solving a problem of configuring fibre channel, a problem that has no official documentation. First there is Snick’s thread in the Openfiler forums. The other source we used was Brian’s How To. Without their generosity I’d probably be bald, and launching expensive equipment through windows (the kind you see through walls with).

More NAS

Wi-Fi System Tools
Check out our Wi-Fi System Charts, Ranker and Finder!

Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!

Over In The Forums

Hi,I've been using Merlin on AC86U for a while, but I've never been fully happy with range because of the lath and plaster plus chicken wire in our wa...
Hi all. I have three Netgear R6250’s at home and looking for your opinions. I am running COX 300/30 internet and will soon be upgrading to 1,000/35 (I...
I am running dnscrypt-proxy with the following in my dnscrypt-proxy.toml:Code: [sources.'opennic'] urls = ['https://raw.githubusercontent.com/DNSC...
Where and witch version merlin softw. we have use to this modem??
For some reasons, when there are constuctions outside, they always hit the internet cable, dont ask my why, second time this year already, there was s...

Don't Miss These

  • 1
  • 2
  • 3