Like every other website on the planet, SmallNetBuilder uses cookies. Our cookies track login status, but we only allow admins to log in anyway, so those don't apply to you. Any other cookies you pick up during your visit come from advertisers, which we don't control.
If you continue to use the site, you agree to tolerate our use of cookies. Thank you!

Router Charts

Click for Router Charts

Router Ranker

Click for Router Ranker

NAS Charts

Click for NAS Charts

NAS Ranker

Click for NAS Ranker

More Tools

Click for More Tools

Wireless Features

Introduction

Perhaps the most frequently asked question we see is "Will a new router give me better wireless performance?" Helping figure this out is a key part of what we do at SmallNetBuilder. But even though we have invested thousands of dollars in test equipment and spend hours testing each wireless router, the answer can still be elusive.

Wireless technology has been on a constant march ever since the powers that be decided 802.11b's 11 Mbps wasn't the end of the wireless throughput road. The progression from b (and its oft-forgotten 5 GHz equivalent: 802.11a) to 802.11n to 802.11ac and soon 802.11ad has created a witches' brew of old and new technologies that frequently causes flaky connections, slow networks and accelerated hair loss among network administrators.

The dirty little secret that wireless router makers don't go out of their way to point out is that their flashy new routers only deliver the bigger numbers on the box when paired with devices (aka clients) that support the same class technology. And the even dirtier secret is that you many times can't get the same class technology for your devices, especially mobile ones.

We're going to refer to wireless Class frequently in this article. If you aren't familiar with the term, please read this article.

The Wireless Benchmarks in our Router Charts let you accurately compare relative wireless performance by always using the same test client. So that the client doesn't limit performance, we use an ASUS PCE-AC66, AC1750 class client. This is a full dual-band 3x3 (three transmit and three receive RF chains) adapter that supports maximum AC link rates of 1300 Mbps in 5 GHz and maximum N rate of 450 Mbps in the 2.4 GHz band. In simple terms, this means that our test results always reflect the best possible performance you can get.

When router and client class are matched, the difference you see in wireless profile charts like the one below is strictly due to router design. But can we use these results to predict how the router will perform with different clients?

Three AC1900 Routers compared - 5 GHz downlink

Three AC1900 Routers compared - 5 GHz downlink

Case 1: Client - Router Mismatch

So you're thinking of stepping up to a shiny new AC router, but don't have any AC clients. Can you expect any performance improvement?

I've been starting to test wireless adapters using this test process, so now have data to provide some examples. The plot below shows 2.4 GHz downlink throughput with three adapters: our standard ASUS PCE-AC66, an ASUS USB-AC56 AC1200 adapter with USB 3.0 port and ASUS USB-AC53 with USB 2.0 connection. Remember that I use 20 MHz bandwidth mode for 2.4 GHz band tests, so throughput may be lower than you would expect.

How To Read The Plot
Throughput vs. Attenuation plots show connection throughput as signal levels change. Signals start out at their strongest level (0 dB attenuation) and move toward their weakest (63 dB in this plot).

The ideal plot, indicated by the bold red line, would stay at the highest throughput throughout the plot until dropping to zero as the connection breaks at its weakest signal level. Real-world devices produce plots more like those shown below, i.e. relatively steady high throughput with strong signals, that falls off gradually until dropping to zero at disconnection.

Larger area under the curve, especially toward the right side, is what you want to see for improved range / performance.

ASUS RT-AC66U - 3 client comparison - 2.4 GHz downlink

ASUS RT-AC66U - 3 client comparison - 2.4 GHz downlink

The AC1750 class PCE-AC66 clearly wins this comparison because it supports a 450 Mbps link rate connection in the 2.4 GHz band vs. the 300 Mbps class connections supported by both AC1200 class USB adapters. (Because we test with 20 MHz mode in 2.4 GHz, maximum link rates move down to 217 Mbps and 130 Mbps.)

The higher class advantage doesn't provide that much throughput advantage with strong signals (left side of the plot). But as signal levels drop toward the right of the plot, the AC1750 class adapter maintains its throughput, while the two AC1200 class adapters start dropping.

The 2.4 GHz uplink plot below shows how performance can differ greatly depending on data flow direction. The PCE-AC66 has about the same maximum throughput, but without the dip with smaller attenuation values anomaly. Both AC1200 adapters, however, lose about 20 Mbps from their maximum throughput levels.

The more interesting observation is that for all three adapters, uplink performance is very similar to downlink starting at 48 dB of attenuation. Note the USB-AC53 still disconnects earliest at 51 dB of attenuation.

ASUS RT-AC66U - 3 client comparison - 2.4 GHz uplink

ASUS RT-AC66U - 3 client comparison - 2.4 GHz uplink

How about 5 GHz? I'll let the plots speak for themselves.

ASUS RT-AC66U - 3 client comparison - 5 GHz downlink

ASUS RT-AC66U - 3 client comparison - 5 GHz downlink

We once again see the signficant benefit from using an adapter whose class matches the router. By the way, that blip at 24 dB showed up in two separate test runs.

ASUS RT-AC66U - 3 client comparison - 5 GHz uplink

ASUS RT-AC66U - 3 client comparison - 5 GHz uplink

Conclusion: To get a significant improvement in range, you need a client as close in class as possible to your router's class.

More Wireless

Wi-Fi System Tools
Check out our Wi-Fi System Charts, Ranker and Finder!

Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!

Over In The Forums

I run an OpenVPN client on my ASUS RT-AC86U with 384.10_2 firmware. Everything works fine except that whenever the VPN client disconnects (happens occ...
View attachment 17763why would a device be trying to access a private IP address from my network....View attachment 17764mysteriously here it is tryin...
Can you use an USB Wifi antena (not those with port like the coaxial cable) for your router to extend and have more powerful Wifi. Some routers have a...
I'm looking for a router that can:- support up to 150Mb/s- support both 2.4GHz and 5GHz- actively monitor network traffic on a per device basis- creat...
I currently have OpenVPN setup on my router to LAN access only. But I need it to assign all the clients the internal DNS server.So I added:Code: push...

Don't Miss These

  • 1
  • 2
  • 3