Like every other website on the planet, SmallNetBuilder uses cookies. Our cookies track login status, but we only allow admins to log in anyway, so those don't apply to you. Any other cookies you pick up during your visit come from advertisers, which we don't control.
If you continue to use the site, you agree to tolerate our use of cookies. Thank you!

Wi-Fi Router Charts

Click for Wi-Fi Router Charts

Mesh System Charts

Click for Wi-Fi Mesh System Charts

Step 5: Security Setup and Final Install

Now that the WRE54G is successfully connected, we can restore wireless security and take a few other security precautions.

A) Restore your AP's security settings. If you turned them off earlier, restore the settings you had. If you did not have security enabled (like to live dangerously, eh?) then this is a good time to enable it.

Find the Wireless Security section of your AP and see what options it provides. Older equipment will probably show only WEP encryption, but newer products should allow selection of WEP or WPA-PSK (Pre-Shared Key). Use WPA-PSK if at all possible, but you'll have to use WEP if only one of your wireless clients can't support WPA-PSK.

While you're at it, if you haven't changed your SSID from the default of "linksys", now would be a good time. The main reason to do this is that it might help keep your wireless clients (and the WRE54G) connected to your WLAN instead of your neighbor's. Pick an SSID that's not obvious and that also doesn't announce to the world where your WLAN is located.

B) After you've set up / restored your WLAN's security and tested it, you can set it up on the WRE54G. Log back into the WRE54G and click on the Edit Security Settings button in the lower middle of the screen. You should then see the screen in Figure 2.

WRE54G Edit Security screen
Click to enlarge image

Figure 2: WRE54G Edit Security screen

Just change the WRE54G's security settings to match those on your AP. Everything must be exactly the same. The Group Key Renewal setting, however, can be left at the default.

Save the settings and close the window and you should now be again looking at the main Setup screen. While you're there, change the SSID to match your AP's, if you changed it.

C) Change the WRE54G password. Anyone who knows the Linksys default password (and who doesn't?) will be able to access your WRE54G's controls and change the settings. Worse, since the shared key is the same on the WRE54G and the AP, they will also have access to your wireless network (assuming they logged into the WRE54G from a wired connection). So, the WRE54G can be a really large security hole.

To change the WRE54G’s access password click the Password link on the main Setup screen to bring up the screen shown in Figure 3.

WRE54G Password screen
Click to enlarge image

Figure 3: WRE54G Password screen

Enter a new strong password, write it down, save the settings and power cycle the WRE54G to get all of your changes into effect. Make sure you put the password someplace where you can find it. Otherwise, the only solution will be to reset the WRE54G's settings to their defaults and redo the whole setup.

TIP TIP: Just Google strong password generator to find one of many tools that will create a nice, new, secure password for you.

D) Move the WRE54G to its location. Now that your have a working and secured WRE54G, you can move it so that it starts doing what you purchased it for. That WRE54G's location needs to be someplace where there is still a good signal from the target AP.

If you locate the WRE54G in an area with poor signal reception, wireless throughput will suffer since speed will be limited by the WRE54G's connection back to your main AP. So choose a location somewhere between the targeted AP and the computer(s) that needs to connect.

Also keep in mind that the actual throughput you get through the WRE54G will be less than half what you would get from a direct AP connection, even if your computer is right next to the WRE54G. That's because the repeating action performed by the WRE54G involves a single radio that has to both receive and retransmit. Still, a slower signal is better than none at all, as long as what you're doing with the connection doesn't depend on speed.

Once you've chosen a location, move the WRE54G to and power it up. In a minute or two you should get two blue lights. Now watch the lights for a few minutes. If you see the top light changing between red and blue, the WRE54G is probably too far from the AP. You may have to experiment to get a location that's a good compromise between speed and range.

Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!

Don't Miss These

  • 1
  • 2