Like every other website on the planet, SmallNetBuilder uses cookies. Our cookies track login status, but we only allow admins to log in anyway, so those don't apply to you. Any other cookies you pick up during your visit come from advertisers, which we don't control.
If you continue to use the site, you agree to tolerate our use of cookies. Thank you!

Router Charts

Click for Router Charts

Router Ranker

Click for Router Ranker

NAS Charts

Click for NAS Charts

NAS Ranker

Click for NAS Ranker

More Tools

Click for More Tools

Wireless Reviews

Wireless Performance

NOTE!NOTES
• Testing was done in using an HP H2210 ipaq running Pocket PC 2003 connecting to a NETGEAR ME102 802.11b Access Point
• Details of how we test can be found here.

The first bad news is that I had trouble getting the SD WiFi to associate with two Broadcom-based 802.11g access points (ASUS WL-300g and Belkin F5D7130). It would see them just fine, but never be able to successfully connect.

I think the problem lies in the card's driver, since I made sure that 802.11b protection was enabled in the APs and even forced one to advertise only 802.11b-compatible transmit rates. I had no problem getting the card to hook up with a NETGEAR ME102 802.11b AP, though, and that's what I used for my testing.

The real bad news, however, is that I've confirmed the observation by other reviewers and users that the card is extremely slow.

SanDisk WiFi - SD WiFi vs D-Link DCF-650W throughput

Figure 6: SD WiFi vs D-Link DCF-650W throughput
(click on the image for a full-sized view)

Figure 6 shows a composite Chariot plot of Location 1(best case) throughput tests for the SD WiFi and D-Link DCF-650W Compact flash 11b card. Since everything in the two tests is the same except the wireless cards (and their drivers) it looks like SanDisk - actually, probably SyChip - has some work to do. I tried runs with Power Save both on and off and there wasn't any appreciable throughput difference.

SanDisk SD WiFi - Four location throughput comparison

Figure 7: Four location throughput comparison
(click on the image for a full-sized view)

The good news, as shown in Figure 7, is that the card's performance doesn't change much with range and its range is comparable to other 802.11b cards that I've tested. The diminutive antenna doesn't appear to limit range, or throughput as some folks have theorized.

Finally, note that there's no throughput hit when enabling WEP. But like most other 802.11b products, the SD WiFi doesn't support Wi-Fi Protected access, either.

802.11b Wireless Performance Test Results

Test Conditions


- WEP encryption: DISABLED
- Tx Rate: Automatic
- Power Save: Disabled
- Test Partner: NETGEAR ME102 Access Point

Firmware/Driver Versions

AP f/w:
1.4h.3
Wireless client driver:
3.00.04.2.0025
Wireless client f/w:
No Info

Test Description Signal Strength (%) Transfer Rate (Mbps) Response Time (msec) UDP stream
Throughput (kbps) Lost data (%)
Client to AP - Condition 1 100 0.315
[No WEP]
0.358
[w/ WEP]
20 (avg)
31 (max)
37 0
Client to AP - Condition 2 66 0.321 19 (avg)
30 (max)
38 0
Client to AP - Condition 3 60 0.326 19 (avg)
31 (max)
38 0
Client to AP - Condition 4 33 0.322 27 (avg)
75 (max)
37 1
See details of how we test.

More Wireless

Wi-Fi System Tools
Check out our Wi-Fi System Charts, Ranker and Finder!

Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!

Over In The Forums

I use RT-AC66U_B1 with firmware ac68u 384.10 and cable speed is 940 Mbps with 500 if I upgrade to a higher version does not exceed 200 with 200
Hi all,Thank you all for this community and Thank You Merlin and the other contributors for the firmware fork.This summer, my port-forwarding stopped ...
Hi guys,I recently migrated my network from a AC3200 and a few range extenders to a AX88U (main router running latest MerlinWRT) with 2 AI Mesch Route...
I just purchased the R7800 router and installed Voxel's latest firmware. I''m coming from Asus routers where I have used them for the past several yea...
I've been unable to post on the Merlin forum and am trying to learn the reason....testing... 1... 2... 3...

Don't Miss These

  • 1
  • 2
  • 3