Like every other website on the planet, SmallNetBuilder uses cookies. Our cookies track login status, but we only allow admins to log in anyway, so those don't apply to you. Any other cookies you pick up during your visit come from advertisers, which we don't control.
If you continue to use the site, you agree to tolerate our use of cookies. Thank you!

Router Charts

Click for Router Charts

Router Ranker

Click for Router Ranker

NAS Charts

Click for NAS Charts

NAS Ranker

Click for NAS Ranker

More Tools

Click for More Tools

Wireless Reviews

Wireless Tests, Continued

But the test of a repeater is how well it extends a WLAN's range or performance vs. range. As I said earlier, I disagree with Linksys' setup suggestion of placing a repeater at the edge of a WLAN's range. So for my testing I chose my medium-range test Location 2. Wireless clients usually do ok here, but tend to get knocked down to the low (Mbps) 'teens in throughput.

Linksys WRE54G - Medium range STA to AP (uplink) Direct vs. Repeater throughput

Figure 8: Medium range STA to AP (uplink) Direct vs. Repeater throughput
(click on the image for a larger view)

Figures 8 and 9 show a very disappointing story. You can see that my client had throughput in the typical low 'teens directly back to the WRT54G, but when I ran the test through the WRE54G, speeds dropped significantly. From the almost 14Mbps direct uplink speed, I'd expect approximately 7 Mbps via a full-speed repeated link connected at the same rate. Similarly, I'd expect about 6Mbps repeated throughput from an almost 12Mbps direct downlink speed.

Instead, I measured slightly less than 3Mbps uplink and 1.6Mbps downlink through the WRE54G repeated link. This tells me that either the link speed between the WRE54G and WRT54G was knocked down further than expected to 802.11b speeds of 11Mbps or lower, there's something wonky with the WRE54G's firmware or some combination of the two. At any rate, clearly Linksys has some work to do to improve the WRE54G's performance.

Linksys WRE54G - Medium range AP to STA (downlink) Direct vs. Repeater throughput

Figure 9: Medium range AP to STA (downlink) Direct vs. Repeater throughput
(click on the image for a larger view)

To eliminate the WRT54G as a possible cause, and see if I could improve the WRE54G's performance, I ran a quick set of tests with an ASUS WL300g as the WRE54G's repeating partner. Unfortunately, I didn't see a significant change in results.

And just before finishing this review I upgraded the WRT54G to V2.04.4 (latest) firmware to check something and decided to repeat the downlink tests. The close range downlink repeated results (lower trace in Figure 7) smoothed out to yield a 10.1Mbps average throughput, but I didn't find appreciable improvement in the medium range tests.

More Wireless

Wi-Fi System Tools
Check out our Wi-Fi System Charts, Ranker and Finder!

Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!

Over In The Forums

Yesterday I installed the Kamoj v5 add-on with my Voxel firmware v1.0.2.75.2. I had some trouble with the addin and wanted to remove it by reinstallin...
If someone is using this on their local machine on the network, is there anyway of forcing them to use my dns servers or blocking it?
I’m hoping for some insight so I can clarify in my own head. Please bear with me. Both are methods of securing my LAN, both mitigate a dynamic WAN IP ...
Would this work?nvram set FORCE_AUTO_UPGRADE=nnvram commitrebootCC
First of all I love the ax1100. I have had it about a week but my sons Playstation was getting a week signal in his basement room. I got the rtac68u t...

Don't Miss These

  • 1
  • 2
  • 3