Like every other website on the planet, SmallNetBuilder uses cookies. Our cookies track login status, but we only allow admins to log in anyway, so those don't apply to you. Any other cookies you pick up during your visit come from advertisers, which we don't control.
If you continue to use the site, you agree to tolerate our use of cookies. Thank you!

Router Charts

Click for Router Charts

Router Ranker

Click for Router Ranker

NAS Charts

Click for NAS Charts

NAS Ranker

Click for NAS Ranker

More Tools

Click for More Tools

Wireless Reviews

D-Link DIR-665

D-Link hasn't shown much love for its first three-stream router, which hasn't had a firmware update in the 13 months or so that it's been available. So I tested with the original 1.00 firmware.

The selectable dual-band router is the only one of the five routers tested that supports three stream N on both bands. It is also the only router in the group to use Marvell's three-stream chipset—the same one Apple used in the just-replaced Airport Extreme Simultaneous Dual-Band Router. Check the 665's review for more details.

The updated 2.4 GHz band performance table for the 665 and TRENDnet TEW-691GR—the only two routers in this round-up to support three-stream N in 2.4 GHz—show the D-Link consistently better than the TRENDnet under the strongest signal test condition in Location A.

Three stream performance - 2.4 GHz band

Figure 4: Three stream performance - 2.4 GHz band

But as signal level drops in Locations C and D the TEW-691GR does as well or better than the DIR-655. In the weakest signal location F, however, the TRENDnet failed to muster enough throughput to run the test in 40 MHz bandwidth mode while the D-Link could.

Still, best case throughput of 93 Mbps from the DIR-665 in Location A, running uplink in 40 MHz mode is just about the same as I previously measured (91 Mbps) using a two-stream test client!

Figure 5 is the IxChariot plot summarizing 2.4 GHz band three-stream downlink tests in 20 MHz bandwidth mode. Throughput is generally well-behaved. But note the tendency to start with low throughput, then switch to higher at the start of some tests. You can really see this in the 20 MHz mode uplink plot linked below. I could not get the effect to go away after multiple test runs.

D-Link DIR-665 IxChariot plot summary - 2.4 GHz, 20 MHz mode, downlink, three stream client

Figure 5: D-Link DIR-665 IxChariot plot summary - 2.4 GHz, 20 MHz mode, downlink, three stream client

Running simultaneous up and downlink tests in location A in Auto 20/40 mode produced the highest total throughput of 125 Mbps.

Here are links to the other 2.4 GHz plots for your perusal:

For the 5 GHz band, my E4200 test commentary covered the DIR-665's performance. I'll just note again that the DIR-665 produced the highest throughput of 93 Mbps running downlink in Location A

The IxChariot plot in Figure 6 again shows the low-to-high switch that occurs at the start of test runs in Location A. You'll see this effect again in some of the other plots linked below.

D-Link DIR-665 IxChariot plot summary - 5 GHz, 20 MHz mode, downlink

Figure 6: D-Link DIR-665 IxChariot plot summary - 5 GHz, 20 MHz mode, downlink, three stream client

Running simultaneous up and downlink tests in location A in Auto 20/40 mode produced the highest total throughput of 124 Mbps.

Here are links to the other 5GHz plots for your perusal:

Closing Thoughts

After testing five three stream N products with a proper three stream N test client, I have to say I'm not impressed with the state of three-stream N right now. Getting a three stream N connection at all was a bit tricky in almost all cases, requiring adapter disables / enables and / or playing with connect modes in the Intel client advanced properties.

This shouldn't be the case. If a three-stream router associates with a three-stream router or AP, you should get three stream rates without having to fiddle with settings. At least right now, that doesn't seem to be the case.

A second observation from this round of testing is that you get the higher-throughput benefit from three-stream N only under very strong signal conditions. Once the signal reduces to even medium levels (as in test Location C), you're pretty much back to two-stream throughput.

In fact, even if you get higher thoughput, the gain isn't that significant. I went through the Performance Tables for the best performing products and picked out the best case throughput measured with two and three stream clients. Considering the cost, lack of stability and slim pickin's for three-stream clients, I'd say the hassle is hardly worth it!

Product 2 stream (Mbps) 3 stream (Mbps)
D-Link DIR-665 90 93
Cisco Linksys E4200 79 89
NETGEAR WNDR4000 83 87
Table 1: Best case throughput - 5 GHz band

Finally, the Intel Centrino "Ultimate- N" 6300 client seemed to like working with the Broadcom and Marvell-based routers more than the Ralink. Link rates tended to be higher and more stable with the NETGEAR WNDR4000, Cisco Linksys E4200 and D-Link DIR-665 than they were with the Belkin N750 DB and TRENDnet TEW-691GR.

I'd expect (hope?) that this can be improved with router firmware and client driver updates. But only time will tell. If Intel's track record of updating its Wi-Fi Link 5300 AGN client drivers is any indication, we should expect a steady stream of tweaks for the 6300.

In the meantime, if you've been thinking that three-stream N will solve your wireless bandwidth problems, think again. The data speaks for itself and says "It won't".

More Wireless

Wi-Fi System Tools
Check out our Wi-Fi System Charts, Ranker and Finder!

Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!

Over In The Forums

HelloI have the ASUS AC86U with Merlin and I have a strange problem .I am connected to a fiber with 1gb provider and I’m getting that speed when I’m c...
Hello everyone,I have seen many cases in this forums speaking about this case in particular, I have tried many things but I couldn't get through it,I ...
Hello @RMerlin could you please add Adguard DNS servers in the preset list ? They do support DNS-over-TLS.Known DNS Providers | AdGuard KnowledgebaseA...
So I tested this FW again and let the router sit for almost 15 minutes and after that amount of time, whatever was causing the CPU spike seems to sett...
Hey guys. This is not the first time this has happened. I turn my TV on and it can't do anything. All the apps say I'm not connected to the Internet. ...

Don't Miss These

  • 1
  • 2
  • 3