Like every other website on the planet, SmallNetBuilder uses cookies. Our cookies track login status, but we only allow admins to log in anyway, so those don't apply to you. Any other cookies you pick up during your visit come from advertisers, which we don't control.
If you continue to use the site, you agree to tolerate our use of cookies. Thank you!

Wi-Fi Router Charts

Click for Wi-Fi Router Charts

Mesh System Charts

Click for Wi-Fi Mesh System Charts

High Power Wireless-N 600mW Gigabit Router
At a glance
ProductAmped Wireless High Power Wireless-N 600mW Gigabit Router (R10000G)   [Website]
SummaryRealtek-based 2.4 GHz 11bgn Gigabit router with high transmit power and very high wired and wireless throughput.
Pros• Very high wired and wireless throughput
• Upgradeable antennas
• User friendly admin layout
• Four guest networks
Cons• Does not provide extended range
• Very weak default WPA/WPS key
• Admin interface can be flaky and requires long reboots to save

Typical Price: $100  Buy From Amazon


Updated 3/29/2012: Added link to wireless retest

The Amped Wireless R10000G High Power Wireless-N 600mW Gigabit Router is the current top of Amped's line of 2.4 GHz 802.11bgn routers. It features a 620 MHz Realtek processor, dual 600mW amplifiers and four-port Gigabit switch. Amped's marketing materials claim up to 10,000 sq. ft. of coverage, which the company backs with a guarantee of 35% off your next router if it fails to meet that promise.

The 10,000 sq ft coverage claim
Figure 1: The 10,000 sq ft coverage claim

The rear of the router has the antenna connectors, a reset switch, WPS button, a power connector, 4 Gigabit LAN ports, and a Gigabit WAN port. The front panel has indicator lights to indicate a connection to ports in the rear.

One nice feature is that it illuminates a number on the front panel to correspond with the port on the rear. Unfortunately, there is no indication as to whether the device has connected at Gigabit speed, which would have been nice.

The router has rubber feet to sit horizontally, but also includes a stand to sit upright as shown in Figure 2. However, I found that the stand did not fit very tightly around the router and the router would often rock backwards on the stand with cables connected. The upright stand also seemed to be an uncomfortable setup when the 5 dBi antennas were connected, but it's there as an option should you not wish to have the router horizontal.

Amped Wireless R10000G connectors and ports
Figure 2: Amped Wireless R10000G connectors and ports

To speed the review along, Tim ran the tests on an R10000G, but sent me a feature-equivalent R10000 to write the feature review. So don't be alarmed when you see "R10000" in some of the screenshots and photos.


The heart of the R10000G is a Realtek RTL8198 SoC, which includes a 32 bit RISC CPU and five port Gigabit switch that supports the four LAN and one WAN ports. A Realtek RTL8192CE 802.11b/g/n 2T2R WLAN SoC and two SiGe SE2576L 2.4 GHz High Power Wireless LAN Power Amplifiers make up the radio. 64 MB of RAM and 4 MB of flash complete the router.

Amped Wireless R10000G board
Figure 3: Amped Wireless R10000G internals

For reference, the R10000 uses a Realtek RTL8196C, which is the 10/100 version of the 8198. It also has 32 MB of RAM vs. the R10000G's 64 MB.

Feature Summary

The R10000G has a nice set of features in an admin interface that is nicely laid out and user-friendly. Here is a list of features R10000G that I complied from its datasheet and admin UI.


    • Static and Dynamic IP, PPPoE , PPTP and L2TP WAN connections
    • MAC address cloning
    • MTU Adjustment
    • DHCP Server, range setting, lease time setting, and default domain
    • DHCP Client list
    • DHCP reservation
    • VLAN support
    • Virtual Server entry for single or multiple ports with TCP, UDP or all protocols forwarded. Enable/disable for each entry.
    • Port filtering – can set individual or range of incoming ports. Allows you to enable or disable TCP and UDP ports on network devices.
    • DMZ Host
    • UPnP enable/disable
    • DDNS support for Dyndns ( and TZO (


    • Firewall enable/disable at each component level
    • VPN Passthrough enable/disable for PPTP, L2TP and IPSec
    • IPv6 pass through on VPN connection enable/disable
    • DoS (denial of service) enable/disable
    • Enable UDP Flood filtering (with settable threshold)
    • Enable TCP-SYN Flood attack filtering (with settable threshold)
    • Ignore Ping Packet from WAN port
    • Remote Management on WAN enable/disable
    • MAC address filtering
    • URL filtering
    • Internet access control - Rule based access control for host (domain name or IP address)
    • Enable/disable bandwidth control with user settable egress/ingress (upload/download) speeds.
    Bandwidth rules list based on IP address (or IP range), port range and protocol

Wireless features

    • WEP, WPA / WPA2 Personal and Enterprise (RADIUS) support
    • 4 guest wireless networks
    • Wi-Fi Protected Setup (WPS) support, pushbutton and PIN
    • Auto and manual channel set
    • Transmission rate set
    • SSID broadcast enable/disable
    • Enable/disable wireless
    • Beacon interval, RTS threshold, Fragmentation Threshold adjustments
    • Wireless MAC address filtering (allow or deny based on MAC address)
    • WMM disable
    • Short GI disable
    • Wireless access schedules
    • Wireless modes: b-only, g-only, n-only, mixed b/g, mixed g/n, mixed b/g/n (default)
    • Channel width 20MHz/40MHz
    • Transmit power adjust, 15%, 35%, 50%, 70% and 100%
    • Wireless network statistics, packets sent/received, active associated clients

Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!

Don't Miss These

  • 1
  • 2