Like every other website on the planet, SmallNetBuilder uses cookies. Our cookies track login status, but we only allow admins to log in anyway, so those don't apply to you. Any other cookies you pick up during your visit come from advertisers, which we don't control.
If you continue to use the site, you agree to tolerate our use of cookies. Thank you!

Wi-Fi Router Charts

Click for Wi-Fi Router Charts

Mesh System Charts

Click for Wi-Fi Mesh System Charts

Features and Administration

Because of its wireless features, the SBX-AC1200P requires a bit more setup work than its wired-only sibling. But Arris tries to make this as easy as possible via the Advanced > Wireless Extender menu in the SBR router's web interface. The options are shown in the screenshot below, with the default being Auto. This means the default extender setup will be a single SSID, with the router's SSID and wireless security password pushed from the router to all SBX-AC1200P extenders. Since I wanted to control the extender's settings I set this to Disable.

Arris SBR-AC1900P Wireless Extender setup

Arris SBR-AC1900P Wireless Extender setup

The SBX-AC1200P comes set to a default IP address, just like the SBX-1000P. So if you need to access the web admin on multiple adapters, you'll need to connect one at a time and give each adapter a different IP address. Once you log in, you'll find an interface much like the SBX-1000P's, with the addition of a Wireless menu. The menu has seven pages starting with the 802.11 Radio page shown below to an Advanced menu. The other submenus are listed in the menu links found in each page's footer, which I highlighted in the screenshot below.

Arris SBX-AC1200P Wireless menu

Arris SBX-AC1200P Wireless menu

The gallery steps through each of the available Wireless admin screens.

The SBR-AC1200P's feature set is surprisingly extensive for an extender. It includes Airtime Fairness, Band Steering, allow / deny MAC address filters and three guest networks per band with ability to allow LAN access in addition to internet for each.

But wait, there's more. If you set the operating mode to Router, the SBX-AC1200P will switch to operating as a wireless-only router. The Gigabit port is now used to connect to a modem and administration is via wireless client only. I won't go through a blow-by-blow description of router features; you can find them in the User Manual. But among the features are:

  • DHCP server with reservations
  • Dyamic DNS client
  • IPv6 and IPv6 firewall
  • Emailed firewall alerts
  • Parental controls with URL filter and web access time limits
  • IPv4 and IPv6 Port range forwarding
  • IPv6 triggered port forwarding
  • DMZ host

The missing menu, at least in the User Manual is one to control the WAN connection. Presumably DHCP client is at least supported.


The SBX-AC1200P is a powerline-connected access point, so end-to-end performance can be broken into two parts: the powerline "backhaul" and AP-to-STA (client) connection. I started by measuring powerline throughput with the SBX in the same Locations A, C and E used for powerline adapter testing. You can learn all about the locations in How We Test Powerline Products. I fired up the SBR-AC1900P to serve as the base router and other end of the powerline connection.

An Acer Aspire S7 running Windows 8 was plugged into an SBR-AC1900P LAN port to form one end of the IxChariot pair. The router itself was plugged into the wall outlet outside my office to bypass the AFCI circuit breaker that protects it.

My trusty Lenovo x220i running Windows 7 traveled among test locations as the other IxChariot endpoint and ran the console. The internal WLAN radio was disabled for powerline throughput measurements and a NETGEAR A6200 USB adapter was used for wireless throughput tests.

The SBR router and SBX adapter radios were both set as follows:

  • 2.4 GHz: 20 MHz bandwidth, Channel 6
  • 5 GHz: 80 MHz bandwidth, Channel 40

The IxChariot plot below summarizes powerline downlink (router to SBX) throughput for the three locations. Throughput decreases quickly as we usually see with powerline products. But it's unusual to see higher throughput in Location E than Location C.

Powerline throughput - downlink

Powerline throughput - downlink

The powerline uplink plots shows the same higher Location E throughput. But so much the better for wireless extension; there is around 110 Mbps of throughput available to the wireless radio.

Powerline throughput - uplink

Powerline throughput - uplink

Location E also represents a wireless dead zone in my home. I can get a barely usable 2.4 GHz there and no 5 GHz signal at all when a router under test is sitting on my test bench. However as noted earlier, the SBR-AC1900P router had to be moved to a spot outside my office, so its AC line cord could be plugged into the powerline test Location A hallway outlet outside my office.

When the NETGEAR R7300DST was sitting in the same spot, I was able to connect directly to the router from Location E on both bands and run tests. But with the SBR-AC1900P, I could connect with a 130 Mbps link rate on the 2.4 GHz band, but not pass traffic. And on 5 GHz I could see the router, but failed to connect. So the SBR-AC1900P can stand to benefit from wireless extension.

The chart below summarizes the results. Here's how to interpret each color bar:

  • Location A Wi-Fi direct represents the maximum wireless throughput achievable with the test setup. It was measured with the test laptop connected to the SBR-AC1900P router, six feet away from it.
  • Location E powerline represents the maximum throughput of the powerline "backhaul" connection between the router and extender. It was measured via with the test laptop connected to the SBX extender via Gigabit Ethernet and wireless shut off in the test laptop.
  • Location E Wi-Fi Extender represents extended Wi-Fi throughput. It was measured with the test laptop connected via Wi-Fi to the SBX extender, located within 6 ft of the extender.

Throughput comparison

Throughput comparison

The results show the 5 GHz extended connection makes almost full use of the available backhaul bandwidth, while the 2.4 GHz extended connection does not. I should note the test notebook linked to the SBX extender at 144 Mbps for 2.4 GHz and 585 Mbps for 5 GHz. These represent maximum 2x2 link rates for each band for standard N and AC products that don't support 256 QAM.

I also included results for the NETGEAR R7300DST and bundled DST6501 extender for comparison (Location C Wi-Fi Extender NETGEAR). The NETGEAR turned in its best wireless extension with the DST extender plugged into Location C vs. Location E because its powerline backhaul throughput was better there. The test notebook was still located in the same Location E spot, so it's a fair comparison. Wireless link rates for the test notebook connected to the DST extender were 72 Mbps for 2.4 GHz and 433 Mbps for 5 GHz, both maximum 1x1 link rates for 802.11n and 11ac.

The upshot of the comparison is the Arris SBR / SBX combo outperformed the NETGEAR DST pair by 44% for downlink and 50% for uplink. But for 5 GHz, the NETGEAR beat the Arris by 15% for downlink and basically tied with it for uplink (2%).

Closing Thoughts

As I've said before, using powerline to connect a wall-plugged AP for Wi-Fi extension can provide a significant performance edge vs. purely wireless extension, in particular when airwaves are crowded and both bands are heavily used. Moving backhaul traffic off the air can lower the airtime load and make Wi-Fi users happier. All this wonderfulness comes true, however, only if the powerline connection is stable and has sufficient bandwidth pass along to the wireless AP.

Backers of would like you to believe it's a superior powerline networking alternative to HomePlug, but my testing shows that's not the case. Comparing average downlink and uplink throughput for all three with all HomePlug AV2 MIMO adapters tested shows the Arris adapters at the bottom of the charts, with the Comtrend PG-9172 alone ranking up among the HomePlug products. Throughput for both and HomePlug AV2 falls off quickly with distance and both are sensitive to high frequency line noise.

Throughput comparison

Throughput comparison

Costwise, an SBR-AC1900P / SBX-AC1200P combo currently costs $180 for the router and $90 for the extender, while the exclusive-to-Best Buy NETGEAR R7300DST bundle of router and extender has dropped to $250 and is currently on sale for $200. Either has a shot at providing decent Wi-Fi throughput to your favorite dead spot. Too bad you can't mix the two; the combination of Arris' SBX-AC1200P extender and NETGEAR's R7300DST router would provide the best of both products.

Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!

Don't Miss These

  • 1
  • 2