Like every other website on the planet, SmallNetBuilder uses cookies. Our cookies track login status, but we only allow admins to log in anyway, so those don't apply to you. Any other cookies you pick up during your visit come from advertisers, which we don't control.
If you continue to use the site, you agree to tolerate our use of cookies. Thank you!

Wi-Fi Router Charts

Click for Wi-Fi Router Charts

Mesh System Charts

Click for Wi-Fi Mesh System Charts

Wireless Features

The K3C defaults to using separate SSID's for each band and auto channel setting. It made a poor choice on 2.4 GHz, setting up on Channel 7 to avoid my house WLAN on Channel 11, but at least used 20 MHz bandwidth mode. I wish consumer router manufacturers would follow what Pros do and use only Channels 1, 6 and 11 in 2.4 GHz.

# of 2.4 GHz streams3
# of 5 GHz streams3
# of Radios2
Radio 12.4 GHz: Intel PSB83513M +Qorvo/RFMD RFFM4252 2.4 GHz front end(x3)
Radio 25 GHz: Intel PSB83523M +Qorvo QPF4519 5 GHz front end (x3)
AntennaInternal printed circuit dipole, 3 per band
Antenna Upgradeable
Wireless Bridge
Notes- Wireless Extension uses Wi-Fi for WAN connection
- Band steering not supported
- 802.11k,vand r roaming assitance not supported

Time Switch in the Basic Wi-Fi settings shown below controls Wireless on/off scheduling. As near I can tell, the only wireless security mode supported is WPA2/AES PSK; WPA, WEP and WPA or WPA2 Enterprise (RADIUS) are not supported. Wi-Fi Protected Setup (WPS) seems an odd omission on a consumer router. But since "mesh" Wi-Fi systems have opted to not support it due to security risks, I suppose it's ok for the K3C, too.

K3C basic wireless settings

K3C basic wireless settings

The Advanced settings don't include anything to control band steering (which Phicomm says is not supported) or airtime fairness, but do let you disable MU-MIMO and beamforming. The AP Isolation Help description says this restricts clients to internet access only. But when I enabled it for 2.4 GHz and connected a Windows 10 notebook, I could reach Ethernet-connected network shares just fine.

K3C advanced wireless settings

K3C advanced wireless settings

Guest Wi-Fi gets its own menu page but supports only 2.4 GHz. Transmit power control is found under the Signal Control menu and offers Low, Medium and High (default) settings, which I assume apply to both bands.

A setting I recommend you don't play with, at least until it's less buggy, is Wireless Extension. This does not set up wireless bridging/repeating on the LAN side of the router. Instead, it uses Wi-Fi as a WAN connection. This is handy if you rely on a wireless ISP for your internet or plan to use the K3C as a travel router. But I found once it was turned on, I couldn't turn it off due to the way the confirmation box blocked me from actually throwing the disable switch. I had to reset the router to default to clear this mode.

K3C advanced wireless settings

K3C advanced wireless settings

Storage Performance

Our standard router storage test procedure was used to measure file copy throughput for FAT32 and NTFS volumes connected via USB 3.0 only because there is no USB 2.0 connector. Media server and Samba encryption were first disabled and USB 3.0 mode enabled to ensure USB 3.0 operation.

The results below are not much to write home about. The FAT32 results landed the K3C dead last for that benchmark for write and read. NTFS results weren't much better, with the K3C second from last for write and fourth from the bottom for read. Note that best-in-class routers achieve over 100 MB/s in all these benchmarks.

Test Description Phicomm K3C
FAT32 Write 18.5
FAT32 Read 34.3
NTFS Write 30.5
NTFS Read 60.2
Firmware Version
Table 2: Storage performance (MB/s)

Routing Performance

The K3C was tested with the V10 router test process, loaded with firmware. Although the simple iperf3 based WAN - LAN & LAN-WAN Throughput tests maxed out at 941 Mbps, the tougher HTTP based tests showed a relatively low score.

Test Description Phicomm K3C
WAN - LAN Throughput (Mbps) 941
LAN - WAN Throughput (Mbps) 941
HTTP Score - WAN to LAN (%) 35.1
HTTP Score - LAN to WAN (%) 34.8
Bufferbloat Score- Down Avg. 528
Bufferbloat Score- Down Max. 420
Bufferbloat Score- Up Avg. 453
Bufferbloat Score- Up Max. 339
CTF Score (%) 100
Firmware Version
Table 3: Routing throughput

Scores on the HTTP Score benchmarks range from 68.1 to 0.3 WAN to LAN and 68.4 to 4.9 LAN to WAN. So the 34.1 and 34.8 land the K3C in the middle of the pack. The plots below show the breakdown for the four filesizes used for the top product for both benchmarks, ASUS' GT-AC5300 the K3C and two other AC1900 class routers, D-Link's DIR-878 and the venerable NETGEAR R7000 Nighthawk. Looks like the K3C could use some improvement in handling smaller file sizes.

HTTP Score comparison

HTTP Score comparison
Plot key file size: [A] 2 KB, [B] 10 KB, [C] 108 KB and [D] 759 KB file

Average Bufferbloat scores again place the K3C in the middle of the tested products. But I've found bufferbloat, at least using our benchmark method, shouldn't be much of a concern, since converting the results back to milliseconds of latency [(1/score) x 1000] yields averages of 1.9 ms downlink and 2.2 ms uplink.

The Cut Through Forwarding tests look for throughput reduction when various router features are used. The 100 score indicates no throughput reduction was found when individually engaging Firewall DoS, Parental Control, QoS or URL Filter features.

Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!

Don't Miss These

  • 1
  • 2