Like every other website on the planet, SmallNetBuilder uses cookies. Our cookies track login status, but we only allow admins to log in anyway, so those don't apply to you. Any other cookies you pick up during your visit come from advertisers, which we don't control.
If you continue to use the site, you agree to tolerate our use of cookies. Thank you!

Wi-Fi Router Charts

Click for Wi-Fi Router Charts

Mesh System Charts

Click for Wi-Fi Mesh System Charts

Upper Chamber

The signals from the device under test (DUT) are picked up by four omnidirectional unity-gain 2.4 / 5 GHz dual-band antennas, shown on the right in the photo below. Because the test client is still 3x3, only three antennas are currently used. The fourth signal path is sealed with connector caps on both ends. You can see there is now lots of room in the cabinet, even with the largest router seen to date, NETGEAR's R8000 Nighthawk X6.

Some readers pointed out that the all-vertical antenna orientation in the V1 testbed might provide a performance edge to routers with vertical antenna polarization. So in the V2 testbed, only one antenna remains vertical; the other two are set at 45°. The two Ethernet and USB connectors and quad power outlets are all filtered so that RF gets neither in nor out.

That's a SNB-installed bamboo rod running across the top of the chamber. It is used to hang the power and Ethernet DUT cables so that they don't get hung up as the turntable rotates the DUT. It's also handy to hang an LED worklight used when setting up routers for test. octoScope provided a plastic crossbar for this, but it was too tall and barely missed the top of the ASUS RT-AC68U's antennas.

NETGEAR R8000 router under test inside the upper test chamber

NETGEAR R8000 router under test inside the upper test chamber

I ran many experiments before settling on the antenna configuration. I found the larger octoBox tended to yield lower throughput than the smaller box, especially for the 5 GHz band. Experiments showed the lower throughput was primarily due to higher path loss from the greater distance between the DUT and chamber antennas.

I found the slightly closer antenna spacing helped compensate for some of the distance-caused path loss. The antenna array is centered on the chamber turntable. Distance from center of turntable to chamber antennas is 18 inches (45.72 cm).

Upper chamber antenna detail

Upper chamber antenna detail

Speaking of which, the octoBox-TT is a new feature in the upper chamber, used to rotate the DUT during testing. Its exact use is described in How We Test Wireless Products - Revison 8. The center of the turntable is approximately XX" from the chamber antennas.


The three antennas are connected to octoScope's new quadAtten programmable attenuator used to adjust signal level to simulate distance. The quadAtten can be seen in the first photo above, mounted on the side of the upper test chamber. The quadAtten outputs are connected to a SMA connectors on the octoBox MPE, which sits between the upper and lower chambers. The MPE emulates multipath using IEEE 802.11n/ac indoor channel models B or C. The lower set of SMA connectors on the MPE connect directly to the lower test chamber, which holds the standard wireless test client (STA).

Lower Chamber

The V2 testbed retires the ASUS PCE-AC66 AC1750 class PCI-e board used as the reference client in V1 testbed. After careful consideration, NETGEAR's R7000 Nighthawk running firmware V1.0.3.60_1.1.27 configured in client bridge mode was selected as the new testbed reference client.

The R7000 is directly cabled to the MPE using dual-shielded cables. Direct cabling is necessary to ensure high enough signal levels in both 2.4 and 5 GHz so that maximum link rates can be reached. Since the R7000 is an AC1900 class router, we now can test the 2.4 GHz side of AC1900 routers to their full potential. The R7000 is connected via Gigabit Ethernet to the Dell Optiplex. The R7000 is managed via web browser from the lower chamber computer. The computer is accessed remotely via VNC.

Lower Test Chamber view

Lower Test Chamber view

That concludes the tour of the V2 testbed. How We Test Wireless Products - Revison 8 describes how we use it.

Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!

Don't Miss These

  • 1
  • 2