Like every other website on the planet, SmallNetBuilder uses cookies. Our cookies track login status, but we only allow admins to log in anyway, so those don't apply to you. Any other cookies you pick up during your visit come from advertisers, which we don't control.
If you continue to use the site, you agree to tolerate our use of cookies. Thank you!

Wi-Fi Router Charts

Click for Wi-Fi Router Charts

Mesh System Charts

Click for Wi-Fi Mesh System Charts


D-Link DAP-2553 AirPremier N Dual Band PoE Access Point

At a Glance
Product D-Link AirPremier N Dual Band PoE Access Point (DAP-2553)
Summary Dual-band, single radio 802.11n business AP /Bridge /Client based on Atheros silicon
Pros • Dual-band
• Can be used as AP, WDS bridge or client
• Can be powered by power wart or 802.3af PoE
• External, upgradeable antennas
Cons • Single radio, so no simultaneous dual-band.
• No WPS support
• Won't extend your 5 GHz range vs. cheaper products

Given the interest that the DAP-1522 garnered as an 802.11n bridge, I asked D-Link to send its business-grade DAP-2553 for review...quite some time ago, in fact. The delay in review is all my fault, so my apologies to D-Link up front for the time it's taken me to get to it.

A lot of 802.11n water has flowed under the Wi-Fi bridge since I looked at the DAP-1522 back in mid-2008. Back then, the 1522 was the cheapest way to add 5 GHz band 11n coverage to an existing LAN.

But now, dual-band APs are very common and you can even pick up a single-radio DIR-628 refurb for under $50, as I write this. However, price isn't the 2553's main claim to fame, but business features like VLAN and 802.3af PoE are.

Figure 1 shows the 2553's back panel, which contains a single 10/100/1000 Ethernet port, reset button and power socket. The three dual-band antennas are connected via RP-SMA jacks, so can be upgraded if you so wish.

DAP-2553 Rear panel

Figure 1: DAP-2553 Rear panel

The front panel is pretty simple, with just indicators for power, 5 GHz, 2.4 GHz (to indicated radio mode) and LAN Link / Activity. The 5 and 2.4 GHz lights just blink at a steady 1 second rate and provide no indication of actual wireless traffic.

Note that there is no mode indicator to show whether the 2553 is functioning as an AP, WDS bridge, WDS bridge / repeater or wireless client. There is also no button to kick off a WPS push-button session, since the 2553 doesn't support WPS, nor a mode switch to manually set AP, Bridge, Repeater or Client mode.

Internal Details

Figure 2 shows the rather fuzzy FCC ID photo, which is clear enough to show the Atheros devices that power it. Fortunately, the internal pictures file had close-ups of the key devices, which are an Atheros AR9132 802.11n 400 MHz Wireless Network Processing Unit (WNPU) and AR9106 Dual-band 3x3 MIMO 802.11n radio.

DAP-2553 board

Figure 2: DAP-2553 board

There was no close-up of the Gigabit Ethernet device, but I'm guessing it's an Atheros AR8121. 16 MB of Spansion flash rounds out the design.


Initial setup was a bit annoying since the 2553 comes set to a fixed IP, which doesn't lie within my LAN's range, instead of grabbing a LAN-compatible IP via DHCP. But after a quick change of my computer's IP address to the 2553's subnet, I was able to log into the admin interface, which isn't password-protected by default.

I'm not going to tour you through the 2553's interface, since D-Link conveniently has an online emulator of the 2553's complete admin GUI. Instead, I'll just summarize the 2553's key features bullet-style:

  • WEP and Personal / Enterprise WPA / WPA2 wireless security
  • Wireless Modes
    2.4 GHz: Mixed 802.11n, 802.11g and 802.11b; Mixed 802.11g and 802.11b; 802.11n only
    5 GHz: Mixed 802.11n, 802.11a; 802.11a only; 802.11n only
  • MAC address filtering
  • 802.3af Power over Ethernet support
  • Tranmit power control (100, 50, 25, 12.5%)
  • Transmit data rate (but limited, see below)
  • Client connection limit (0-64, 20 default)
  • Up to four SSIDs, each with separate wireless security
  • Up to four VLANS w/ 802.1q tagging
  • "Rogue" AP scan
  • Wireless access enable / disable schedule
  • Four level priority-based QoS
  • DHCP server with IP reservaton
  • Telnet, SSH, SNMP, HTTP, HTTPS admin interfaces
  • Client-to-client and client-to-wired-LAN partitioning
  • Ethernet and WLAN statistics
  • Logging

The feature set provides a bit more than your average consumer wireless router and makes for a relatively full-featured AP. Emailed alerts, to go along with the "rogue" AP scan (D-Link calls this feature "Intrusion Dection, which is really isn't), and log / statistics summaries would have been nice.

As noted earlier, Wi-Fi Protected Setup (WPS) isn't supported, since it's not used in the business environment that the 2553 is intended for. The Transmit Data Rate control was only available when a mode that included 11n wasn't selected.

I didn't try the WDS bridging features of the 2553, but did try Wireless Client mode. Figure 3 shows that you need to select a band before you scan. So you'd better assign both the wired device and the 2553, static IPs in your LAN's subnet, but outside your LAN's DHCP server, so that the two can communicate. Once you get connected, which isn't obvious from the Wireless Settings page by the way, you can change your client to use DHCP so that it gets proper gateway and DNS settings.

DAP-2553 set as wireless client

Figure 3: DAP-2553 set as wireless client

Actually, the way I initially tried this was to keep the 2553 attached to my LAN's switch while I set it to client mode and scanned. Once it picked up my LAN's wireless AP, I selected it, entered the WPA2 passphrase and waited. Once I saw all the LEDs on my LAN switch start blinking madly—due to the network storm caused by the switch port-to-port connection made by the new wireless connection—I knew that the 2553 had connected.

Support Us!

If you like what we do and want to thank us, just buy something on Amazon. We'll get a small commission on anything you buy. Thanks!

Don't Miss These

  • 1
  • 2